Danfoss TS715 Si User Manual download pdf (Page 2)

User Instructions

To move to

next event

To alter clock

& ON/OFF

times

To move to

next day or

to weekend

Fig.1

Fig.2

Fig.3

Fig.4

Fig.5

Fig.6

Fig.7

Fig.8

Fig.9

Before beginning programming, you should reset the unit. Open the flap on the front of the clock.

Press the RESET button using a non-metallic object (e.g. a pencil or end of a bic biro pen top).

This will clear all previous pre-set programmes (Fig.1)

A. Setting the correct Time and Day

TIME - Press PROG once (Fig.2). The words SET TIME will appear at the top of the

display. The time will flash on and off (Fig.3). Use the + and - buttons to set the correct

time (Fig.4)

DAY - Press DAY repeatedly until the correct day of the week is displayed (Fig.5). MO is

Monday, TU is Tuesday etc

B. Accepting the Factory Pre-settings

The TS715 comes ready programmed with a set of time and temperatures to suit the

average household (see Factory Presettings page 4).

To accept these settings press the PROG button until the time appears and colon in the

display begins to flash - the unit is now in RUN mode (Fig.6).

If you wish to alter these settings follow the instructions below.

Your installer will have set your unit to operate in one of the following modes:

5/2 day - one set of programmes for weekdays and another for weekends (Section C)

7 day - different settings for each day of the week (Section D)

24 hour - one set of programmes for the whole week (Section E)

See INSTALLER SETTING tick box on inside flap label to ascertain

which mode your unit is set and follow relevant instructions below.

C. Programming the system - 5/2 day mode

1. Press PROG until SET ON TIME appears at the top of the display and MOTUWETHFR

appears at the bottom of the display (Fig.7). Use the + and - buttons (Fig.4) to set the time

you would like your heating to first come on in the morning (Event 1).

2. Press NEXT ON/OFF once only (Fig.8). Use the + and - buttons (Fig.4) to set the time

you want your heating to go off (Event 2). To move to the next setting, i.e. when you would

like your heating to come on again (Event 3) press the NEXT ON/OFF button again.

3. Continue programming the central heating ON and OFF times for weekday Events 4,

5 & 6 as in Step 2.

4. Press the DAY button once (Fig.5) and SASU will appear at the bottom of the display

(Fig.9). Either press COPY (Fig.10) to keep the same settings for Saturday and Sunday

as you have programmed for Monday to Friday. Alternatively, programme new ON/OFF

times by pressing the NEXT ON/OFF button (Fig.8) to move to the next setting and using

the + and - buttons (Fig.4) to set the time you want.

5. Press the PROG button (Fig.2) to return the unit to RUN mode

6. Proceed to Section F

D. Programming the system - 7 day mode

1. Press PROG until SET ON TIME appears at the top of the display and MO appears at

the bottom of the display (Fig.11). Use the + and - buttons (Fig.4) to set the time you want

your heating to first come on in the morning (Event 1).

2. Press NEXT ON/OFF (Fig.8) to move to Event 2. Continue programming the central

heating ON and OFF times in this way by using the + and - buttons to set the time you

want and pressing the NEXT ON/OFF button to move to the next setting and (Fig.4 & 8).

3. Press DAY button once only (Fig.5). TU will appear at the bottom of the display. Either

press COPY (Fig.10) to keep the same settings as the day before or continue programming

for the rest of the week by pressing the NEXT ON/OFF button to move to the next setting,

using the + and - buttons to amend the time, and by pressing DAY to advance to the next

day.

4. Press the PROG button (Fig.2) to return the unit to RUN mode

5. Proceed to Section F

Fig.10

INSTALLER SETTING

24 Hour

5+2 Day

7 Day

1 2 3 4

Comments to this Manuals

No comments

Danfoss TS715 Si User Manual Page 2

Comments to this Manuals

Related products and manuals for Thermostats Danfoss TS715 Si