Danfoss TP7000 User Manual download pdf

Datasheet

TP7000, TP7000-RF and TP7000M

Programmable Room Thermostats

Features

The TP7000 combines the functions of a time clock

and room thermostat into a stylish, simple to use

controller that allows the user to programme

different temperatures for different times to

match lifestyle demands. The TP7000 o ers true

7-day programming, allowing each day to be

set di erently if so required. In addition, the unit

can be set to 5/2-day mode allowing one set

of programmes to be used for weekdays with a

di erent set being available for the weekends.

TP7000 is available in hard wired versions and in

labour saving RF versions. Both hard wired and

RF models o er up to six temperature changes

each day and include the option of programming

an “O ”.

TP7000 offers several advanced features which

can be selected by the installer at the time of

installation, these include:

• Optimum start control : This feature uses internal

temperature to calculate the time in advance

of programmed time that the system must

switch on in order to ensure that programmed

temperature is achieved by the programmed

time.

• Chrono-proportional control: This feature de nes

the boiler cycle rate and the on/o times of the

boiler within the cycle. This adds to comfort

and improves boiler e ciency, particularly with

condensing type boilers.

RF models incorporate a digital FM radio transmitter

which transmits a unique thermostat identity

code which is learnt by the RX receiver during

commissioning. Receivers, which are available in

1, 2 & 3 zone versions, can be mounted up to 30

metres from the thermostat and can be used to

switch boilers, pumps or control valves.

The range includes battery and mains powered

versions in both built-in and remote sensor types,

please refer to the data table for details and

ordering codes.

• 7-day or 5/2 day programming options

• Up to 6 time and temperature events per day

• Available in hard wired and RF versions

• Hard wired versions available for battery and

mains operation

• Holiday programming mode and thermostat

mode

• Many user overrides including programme

extension

Installer Settings -

DIL Switches

All models

5/2 day programming 7 day programming

Optimum start contoller enabled Optimum start contoller disabled

Chrono-proportional control On/Off control

TP7000, A, B, AB, M, M, MA, RF & A-RF models with 3/6 cycles per hour option

Chrono-proportional, 6 cycles / hour Chrono-proportional, 3 cycles / hour

TP7000C, CA, CM, CMA, C-RF & CA-RF models with 6/12 cycles per hour option

Chrono-proportional, 12 cycles / hour Chrono-proportional, 6 cycles / hour

Note: Sw

is only active if Sw

is set to chrono-proportional mode

Part No. 560v08 03/08

1 2 3 4

Summary of Contents

Page 1 - Programmable Room Thermostats

DatasheetTP7000, TP7000-RF and TP7000M Programmable Room ThermostatsFeaturesThe TP7000 combines the functions of a time clock and room thermostat into

Page 2 - Datasheet

2DatasheetPart No. 560v08 03/08TP7000 Series - Programmable Room ThermostatsInstaller Settings - Optimum Start ControlIf DIL SW2 has been set to Opti

Page 3

Datasheet3Part No. 560v08 03/08TP7000 Series - Programmable Room Thermostats1234ELECTRONICSNLCOMZONE1 ONZONE1 OFF1234ELECTRONICSBZONE2 ONCCOMZONE1 ON

Page 4

Datasheet4Danfoss can accept no responsibility for possible errors in catalogues, brochures, and other printed material. Danfoss reserves the right to