Danfoss TripleLynx CN Installation Manual Page 164
- Page / 268
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Configuration at a PC
Solar-Log1000, 500, 200: Configuring inverter data (Basic/Inverter)
164 of 268 Solar-Log
1000/500/200
Installation
Pac correction factor
If the power yield displayed by the inverter is compared with the calibrated
current meter, a certain deviation is found. An approximate correction fac-
tor can be defined in order to compensate for this inaccuracy.
All yield data are stored internally without any correction factor. This factor
is applied only when the data are displayed. The factor can therefore be
adjusted at any time.
The formula for calculating the correction factor is as follows:
Yield on current meter / Yield at inverter * 1000
If the inverter does not have a display, the correction factor must be left at
1000 initially, and the factor can then be determined after about a week.
Enter the required value.
Name
You can enter your own name for the inverter here.
Module field
Each connected string is allocated to a module field. Module fields are sub-
divided according to solar module type, inclination and alignment. If all
modules within a system are of the same type and have the same align-
ment, only one module field, e.g. “1”, is defined. Strings not used must be
switched off (switched to “0”)
Other module fields must be defined for modules with different alignments.
Ideally, each field should be made up of at least two individual strings,
which monitor each other.
Example:
An installation with 23.6 kWp is divided into 3 × SMA SB5000TL and
2 × SMA SB2500. 18 kWp is located on a barn roof with 30° inclination,
20° South-East deviation, and 5 kWp on an adjoining garage roof, 32° in-
clination, 0° South deviation.
Location
Inverter
String power
Module field
Barn
1.SB5000TL
2000
1
Barn
1.SB5000TL
2000
1
Barn
1.SB5000TL
2200
1
Barn
2.SB5000TL
2000
1
Barn
2.SB5000TL
2000
1
Barn
2.SB5000TL
2200
1
Barn
3.SB5000TL
2000
1
Barn
3.SB5000TL
2000
1
Barn
3.SB5000TL
2200
1
Garage
1.SB2500
2500
2
Garage
2.SB2500
2500
2
All connected strings allow mutual monitoring, the strings in module field 1 allow
multiple monitoring, and the two strings in module field 2 mutual monitoring.
Enter the required value.
- Installation manual 1
- Contents 2
- Contents 3
- Installation 3 of 268 3
- 4 of 268 Solar-Log 4
- Installation 5 of 268 5
- 1 Safety information 6
- 1.3 Electric current 7
- 2 Assembly instructions 8
- 2.2 Wall mounting 9
- Wall mounting 10
- 3 Unit connections 11
- 3.2 Solar-Log 12
- (Solar-Log 13
- 3.4 RJ45 configuration 14
- 3.5 Connection accessories 15
- 4 Connecting the inverters 16
- De-energising the inverter 17
- De-energising the Solar-Log™ 17
- 4.2 SMA 18
- Figure 10, left) 19
- Figure 10, right) 19
- 4.3 Kaco – Powador 25
- Kaco – Powador 26
- 4.4 Kaco – PVI-BluePlanet 27
- SolarMax – S and C series 28
- 4.6 SolarMax – Cx series 30
- 4.7 SolarMax – E series 32
- 4.8 Fronius with ComCard 34
- 4.9 Danfoss 36
- 4.11 Power-One/Aurora 39
- 4.12 Sunways – AT/NT 41
- Solutronic SP25-55 (RS485) 44
- Schüco SGI series (RS485) 47
- 4.17 REFUSOL 49
- REFUSOL 50
- 4.19 Mastervolt (RS485) 54
- 4.20 AEG PS (RS485) 56
- 4.21 Eaton (RS485) 58
- 4.22 Suntension (RS485) 60
- 4.23 Riello (RS485) 62
- 4.25 Ingeteam 65
- 4.27 Conergy (only Solar-Log 68
- 4.29 Effekta 71
- 4.30 ALPHA-SOL 73
- 4.31 Europa-Solar AG (RS485) 75
- Page 162) 77
- 4.33 Evoco 79
- 4.34 Powercom 80
- 4.35 SALICRU EQX 83
- 4.36 SALICRU EQXLV 85
- 4.37 Santerno 86
- Santerno 87
- Schneider Electric SunEzy 88
- 4.39 Steca 90
- 4.40 WINAICO 91
- 4.41 Delta (RS485) 94
- 4.42 Sungrow 95
- 4.43 Sustainable Energy 97
- 4.44 Motech (RS485) 98
- 1000/500/200 100
- 4.46 AROS Solar Technology 101
- 4.49 Hyundai HPC-250HT-E 105
- 4.50 EKO Energy 107
- 4.51 Q3 (RS485) 108
- 4.52 Siemens 109
- Siemens 111
- Page 17 112
- Page 15) 112
- 4.54 Albatech APL monophase 114
- 4.55 Enfinity 115
- 4.56 Carlo Gavazzi 116
- 4.57 Omron 118
- 4.58 Samil Power 119
- 4.59 Aten 120
- RJ14 socket pin allocation 121
- 4.60 Pairan 122
- 4.61 Schneider Electric 123
- 4.62 Eaton 124
- 4.63 Ginlong 126
- 4.64 Growatt 127
- 4.65 Oelmayer 128
- 5 Connecting accessories 130
- Connection 131
- 5.3 Sensor Box 132
- Sensor Box 133
- 5.4 Sensor basic 134
- 6 Other connections 136
- Connection through S0 output 137
- , Solar-Log 138
- relay 139
- e-mail 139
- 7 Starting up 140
- Adjust the Date/Time 142
- Inverter selection 143
- Page 251) 145
- Page 209) 145
- Page 211) 145
- 7.6 LED status displays 147
- 8 Configuration at a PC 148
- Configuration at a PC 149
- Solar-Log 149
- Installation 149 of 268 149
- Page 213) 150
- Network settings 151
- Internet access 151
- Network router 151
- analogue modem (Solar-Log 151
- GPRS modem (Solar-Log 151
- Preset “0” 152
- Dial tone Off 152
- Allow dial in 152
- Dial in password 152
- Page 13) 153
- WLAN 154
- Network selection 154
- – IP Address, Subnet Mask 155
- – Gateway 155
- – Alternate DNS server 155
- 8.5 Solar-Log 156
- 8.6 Solar-Log 158
- 8.7 Solar-Log 160
- (Basic/Inverter exchange) 160
- 8.8 Solar-Log 162
- 500/1000 163
- Enter the required value 164
- • A consumption meter 165
- Enter required scaling 167
- Click on Save 167
- System data 168
- Target/actual calculation 168
- Page 162) 170
- (Extended/Internet) 172
- Page 265 174
- Periodic data export 175
- Page 253 176
- Page 265) 177
- Inverter 181
- Section on code selection 181
- PM+ (Extended/Power 182
- Management) 182
- Monitoring and logging 183
- Inverter control 183
- Networking 183
- Reactive power control 183
- Fixed cos φ shift factor 184
- Data correction 187
- Data import 187
- Data backup (automatic) 187
- Data backup (manual) 187
- System backup 189
- System settings 189
- configuration 189
- 9 Solar-Log 193
- : Configuration at the unit 193
- 9.2 Navigation overview 194
- Page 200) 198
- an inverter 199
- as a consumption meter 199
- Re-detection of inverters 200
- Delete data 203
- Delete inverter 203
- Restore factory settings 203
- 10 Solar-Log 204
- Buttons 205
- Selection lists 205
- Input boxes 206
- Virtual keyboard 206
- Radio buttons 206
- 206
- 206
- Check boxes 207
- Confirmation dialogue box 207
- 10.3.2 Inverter selection 210
- Inverter selection order: 210
- Inverter detection 211
- Page 223) 213
- Alternate DNS server 215
- User 217
- Password 217
- SIM PIN code 217
- Test field strength 218
- Always stay online 218
- SMS directly over modem 218
- 10.6 Solar-Log 219
- Page 241) 221
- Setting the S0 meter 225
- Connect. module power 225
- Module field (1-9) 225
- String 227
- Module field 227
- Connect. module pwr 228
- Name 228
- Configuring the monitoring 229
- Active, Inactive 229
- Configure the message 230
- Message by 230
- Page 167) 231
- Page 170) 231
- System group 232
- Feed-in tariff 232
- Yearly target 232
- Jan to Dec 233
- Page 265 234
- Page 217) 236
- Testing the connection 238
- Test EMail, Test SMS 238
- Last transmission 238
- Status 238
- WEB activated 239
- Update interval 239
- Start test transmission 240
- Close relay 240
- Send e-mail 240
- (Extended/Large display) 241
- (Extended/Alarm contact) 243
- RS485-A 244
- RS485-B 244
- Test 244
- Please choose: 245
- Date 246
- Day value 246
- Pin Code, Repeat 248
- Delete data 249
- Initialiser yield data 249
- Current firmware 250
- 11 Faults 252
- 11.2 Fault messages 253
- Faults 254
- 254 of 268 Solar-Log 254
- Installation 254
- Installation 255 of 268 255
- 256 of 268 Solar-Log 256
- 11.3 Inverter fault messages 257
- Figure 14: Reset button 258
- Restarting 259
- 12 Disposal 260
- 13 Technical data 261
- Appendix 263
- Homepage Service 265
- List of figures 267
Related products and manuals for Power adapters & inverters Danfoss TripleLynx CN
(177 pages)
(1 pages)© 2020, manymanuals.com. All rights reserved. | 0.110 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals